Free Energy News » magnet

Dr. Stiffler SEC Exciter Hydrogen production via diode

F.E.N. — Wed, 23 Jun 2010 23:56:12 +0000

www.overunity.com Dr. Stifffler experiment with a SEC exciter circuit running from a 12 Volts battery to generate Hydrogen via a normal 1N4148 diode in destilled water. Very scalable and thus input power independant.

Probably a scam : Muammer Yildiz magnet motor presentation at Eindhoven TUe in 2009

F.E.N. — Mon, 26 Apr 2010 23:28:00 +0000

www.overunity.com Probably hidden batteries are used: This was already taking place on 27th of April 2009 at the TUe in Eindhoven. Muammer Yildiz presented his magnetic motor together with JL Duarte but until now nobody posted videos or pictures about this event. Yildiz is search via a penelty order in Germany. www.overunity.com

“Orbo Replication” temperature experiment uncut

F.E.N. — Mon, 26 Apr 2010 22:36:56 +0000

See globalfreeenergy.info for details. This is the entire uncut video, with comments. This was my first “Orbo Replication” temperature experiment. Actually it’s magnets spinning on a Dremel drill over a toroid. It shows an amazing “Orbo Replication” effect. Magnet temperature drops far below ambient. Starting temperature is near 69F. I’ve tested various theories such as electrostatic cooling. It’s not caused by such. Experiments show heat from air friction is far greater than electrostatic cooling in these experiments. It’s true that if surrounding ambient temperature is lower than magnet temperature, then magnetic temperature will drop. That is not the case, as you will see. Ambient temperature is 67F to 69F. The temperature of the spinning magnets drops to 64.6F. As soon as the toroid is disconnected from the diode, the temperature of the magnets suddenly beings increasing, where it goes back up the ambient temperature. Since then, I’ve confirmed “Tiny Orbo Replication 4″ clearly produces excess energy. Input = 180mW. Output from 1 pickup coil alone = 280mW. Input = 180mW. Output from 1 pickup coil alone = 280mW. Congratulations Sean McCarthy & Steorn!!!

Probably a scam : Muammer Yildiz Magnet Motor delft university

F.E.N. — Wed, 21 Apr 2010 23:50:29 +0000

www.overunity.com Probably a scam : Muammer Yildiz Magnet Motor presentation at the delft university in the netherlands Probably hidden batteries are used. www.overunity.com

Holy Grail “Tiny Orbo Replication 4″

F.E.N. — Fri, 16 Apr 2010 16:19:45 +0000

Input: ~ 180 mW total. 170 mW of that 180 mW is joule heating from electrical wire resistance, thus leaving 10 mW for the motor. Output: ~ 280 mW from one pick up coil. Also, Ive taken a guesstimate that the heat produced by this motor due to bearing and air drag is ~~ 2 watts. For part #’s & build instructions: globalfreeenergy.info The motor mounting is incomplete, so don’t build the mount as shown in the video. Both ends of the metal rod need to be mounted, otherwise there will be axial forces on the bearing. I’ll update the video when it’s all 100% complete. Contact me for details. The rpm was 17100.

Tiny Orbo Replication 3

F.E.N. — Sun, 28 Mar 2010 07:19:01 +0000

This is the “Tiny Orbo Replication” ver.3. Ver.1 was tested at far above 100% efficiency. See globalfreeenergy.info Ver.3 is not complete yet. Only 1 toroid. Needs 16 toroids. Everything is taped down for now. It’s still under construction. Input power is ~ 0.12 watts. Nearly 100% is joule heating (wasted heat), & does not go to powering the motor. Max rpm was 13500, where the motor was still rapidly accelerating, but something went wrong. It began to rapidly decelerate. Decades of experience tells me without any doubt this motor is far beyond 100% efficiency. Congratulations Sean & Steorn! In this video you’ll see the motor run, but first some footage while it was being made. Warning, it’s loud. I have no idea why. The bearing is a good new ceramic bearing. The meter shows frequency, not rpm.Multiply it by 7.5 to get rpm. 1.4KHz = 10500 rpm. This toroid is very special. It’s Metglas MAGAMP, perm=1 million, but the large plastic case was removed. Core was then Epoxied. After the core was wound, the perm changed to nearly an air core caused by pressure, which is a well known effect. This effect seems to greatly amplify the excess energy effect, turning the motor into a monster. Even though the perm nearly = a vacuum, the toroids work great for this design. Sean, you did it brother!!! I am not affiliated with Steorn. Orbo is trademarked by Steorn, steorn.com. You can find daily blogs about my replication progress at http

Magnet Motor Switch Secondary Coil Test

F.E.N. — Fri, 26 Mar 2010 14:52:00 +0000

Testing a short length of wire as a secondary. Next step is to put on a full size secondary coil.

bemf “fun with fans”

F.E.N. — Sat, 20 Mar 2010 05:47:51 +0000

Using the same Bedini schematic similar to “magnet spiner” www.youtube.com and inspired by Imhoter made two fun-motors, running from 6v bttry. First one does not charge the same bttry but charging the cap from which second motor’s running, charging it’s own capacitor.

Magnet Motor Coil Switch

F.E.N. — Thu, 18 Mar 2010 04:01:05 +0000

My Design for making a make and break switch.

“Tiny Orbo Replication 2″

F.E.N. — Sun, 14 Feb 2010 04:28:52 +0000

Update on present progress. Core is a Metglas MAGAMP, permeability is 1 million. 4 NdFeB magnets. Old junkie ball bearing with grease removed. When the rpm gets to about 8000 it begins to float and wobble. Looks like it wants to fly away. For updates see globalfreeenergy.info Still trying to get the losses from electrical resistance down relative to output. If we disregard the losses from electrical resistance, then this motor is measured at far above 100% efficiency. Way to go Steorn! I am not affiliated with Steorn. Orbo is trademarked by Steorn.